NRPavs   SOLD items 2014 archive 1  NAD  319  stereo amplifier   details
SOLD items 2014 archive 1 product details : 
NAD  319
stereo   amplifier
SOLD
NAD  319  stereo  amplifier
NAD  319  stereo amplifier  :  controls  closeup
NAD  319  stereo  amplifier  :  left  profile
NAD  319  stereo amplifier  :  back  view
NAD  319  stereo  amplifier  :  top  view
NAD  319  stereo amplifier  :  size  scale
   SOLD January 2014 on trademe  to Grey Lynn, Auckland
S/N: G7931900510
 
 
  sitemap    NAD  319  stereo amplifier 2nd unit  specifications                         ack to NRPavs Home  
        NAD   319  stereo amplifier  - charcoal grey :                 

   • 2 x 125 Watts continuous power into 8 ohms
   • 2 x 400 Watts dynamic power into 2 ohms
   • Remote control capable
   • Building Block Concept: Power amp is Model 216THX,    • Pre-out / Main-in
   • All Discrete circuitry
   • Tone controls defeat switch
   • Bridgeable: 400 Watts into 8 ohms, one channel
   • Input switching through relays with Gold Plated contacts
   • Soft Clipping

   Since its introduction, the NAD Model 216THX Power Amplifier has enjoyed a strong following and tremendous reputation throughout the world for its performance and reliability
   The latest addition to NAD’s range of integrated amplifiers is the Model 319 which is very closely related to the Model 216THX. In fact, the entire power amplifier inside the Model 319 is identical to that of the Model 216THX

   Flexibility :
   Flexibility is a traditional strong NAD point. The Model 319 has 6 line inputs (including 2 tape in/outputs with dubbing facility both ways). By removing the links between the Pre-out and Main-in sockets the preamplifier section can be separated from the power amplifier for easy upgrades (bi-amping, for instance) or adding ancillary equipment
   As the built-in power amp of the Model 319 is identical to that of the NAD Model 216THX you can easily triple the output power to your speakers by adding a Model 216THX to your system. Bridge both power amplifiers and you have increased the power of your system to 2 x 400 Watts continuous into 8 ohms
   Thanks to this “Building Block Concept” your Model 319 doesn’t need to be made redundant to upgrade

   Performance :
   Rather than using electronic switching between sources, the NAD engineers have opted for using relays as these will give better performance at this price level. To ensure long term reliability only relays with gold plated contacts have been used. The input selector relays are located as closely as possible to the input sockets to minimise cross talk and interference
   As with the relays, all input and output sockets are gold plated to ensure reliable signal transfer. A generous power supply (the same massive Holmgren™ Toroidal transformer as the Model 216THX is used) and over-rated output devices ensure low noise and low distortion

   Integrated Amplifier :
   The overall high level of performance is achieved by using discrete circuitry only and high quality close tolerance components such as metal film resistors and polypropylene capacitors. As one would expect from any NAD amplifier, the Model 319 will drive loudspeakers with complex loads (such as low impedances) with great ease
   The Model 319 also incorporates NAD’s acclaimed switchable “Soft Clipping” circuit which significantly reduces the risk of damage to loudspeakers due to prolonged high power operation
   Convenience, flexibility and, above all, performance, are the hallmarks of the NAD Model 319. Consistent with NAD’s reputation the Model 319 is somewhat of a bargain when compared to amplifiers with similar performance


Specifications :
  -:®:-    Vintage : 1999 model
   PRE-AMP SECTION :
  -:®:-    Input sensitivity : 80mV ref. 0.5V
  -:®:-    Signal / Noise ratio (A-weighted) : 85dB ref. 1W
  -:®:-    THD (20Hz to 20kHz) < 0.04%
   Line level inputs :   Input impedance (R and C) : 20kohms / 450pF
  -:®:-    Input sensitivity [ref. 0.5W] : 80mV
  -:®:-    Signal / Noise ratio [A-weighted ref 1W] : 85dB
  -:®:-    Frequency response [20Hz to 20kHz] : ± 0.2dB
  -:®:-    THD : 0.01%
   Line level outputs :   Output impedance : Pre-amp 220ohms   Tape Source Z + 2k ohms   Phones : 220ohms
  -:®:-    Maximum output level : 12V   Tape : 10V  Phones > 8V into 600ohms, > 250mV into 8ohms
   Tone controls :   Treble : &pusmn; 7dB at 10kHz   Bass : ± 10dB at 50Hz
   POWER AMP SECTION :
  -:®:-    Continuous output power into 8 ohms 125 Watts (21dBW)at rated distortion :(THD 20Hz to 20kHz) : 0.03%
  -:®:-    Clipping power [maximum continuous power per channel] : 150W [21.8dbW]
  -:®:-    IHF Dynamic headroom at 8 ohms : +1.3dB
  -:®:-    IHF dynamic power [maximum short term power per channel] : 8ohms 170W (22.3dBW),   4ohms 280W (24.5dBW),    2ohms 400W (26.0dBW)
  -:®:-    Damping factor [ref. 8 ohms, 50Hz] : > 200
  -:®:-    Input impedance : 60kohms / 500pF  Input sensitivity (for rated power into 8 ohms) : 1.12V
  -:®:-    Frequency response : 2Hz to 100kHz [-3dB]  +0dB, -3dB,  [20Hz to 20kHz ± 0.2dB]
  -:®:-    Signal / noise ratio [ref. 1W] : 96dB   ref. rated power : 117dB with THD (20Hz to 20kHz) < 0.03%
  -:®:-    Remote : non-original HTR 2 remote    NAD Link : Yes
  -:®:-    Dimensions [W x H x D]: 435 x 145 x 380mm   Weight : 14kg, packed weight : 15.5kg


   SOLD January 2014 on trademe  to Grey Lynn, Auckland












sitemap


Google
www NRPavs




{{ back to the top        Back to Oldies but Goodies  - stereo  amplifiers


© NRPavs   2006 - 2014    All Rights reserved